Printable version

Drivers & software

Important Note Not the product you are looking for? If you cannot find your product on this site, go to HP Support Center .

* RECOMMENDED * HP T1000j Uninterruptible Power System Firmware Update

By downloading, you agree to the terms and conditions of the Hewlett Packard Enterprise Software License Agreement.
Note:  Some software requires a valid warranty, current Hewlett Packard Enterprise support contract, or a license fee.

Type: Firmware - UPS
Version: 1.10(21 Oct 2011)
Operating System(s): OS Independent
File name: SP55015.EXE (1.6 MB)
This softpaq includes firmware for the HP T1000j Uninterruptible Power System (UPS). Detailed instructions for performing the firmware update are included in the softpaq.

To ensure the integrity of your download, HP recommends verifying your results with this MD5 Checksum value:

d2ee8e676c92656adc1584c776288426 SP55015.EXE

Reboot Requirement:
Reboot may be required after installation for updates to take effect and hardware stability to be maintained.


Installation:
Download the SoftPaq to a directory on your hard drive and change to that directory.

The file that is downloaded is an executable with a filename according to the SP Number.

Run the SP executable to unpack the firmware and release information.

From that SP directory, use the detailed instructions located in the HP T1000j UPS Firmware Update Instructions.pdf file to perform the update.


End User License Agreements:
Hewlett-Packard End User License Agreement


Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


  • Modified the UPS input waveform detection scheme sub routine. This repaired a unique case in the firmware that allowed the UPS transfer time to battery operation to take excessive time, when utility dropped down from 100 volts to 60 volts under certain conditions.
  • Modified the Advanced Voltage Regulation (AVR) detection scheme by reducing the number of cycles required to detect an out of tolerance voltage condition. This repaired an issue in the firmware that allowed the UPS to stay in its current AVR mode and not perform a buck or boost cycle quick enough, which resulted in the output voltage falling outside of the output voltage specification when utility dropped down from 100 volts to 60 volts under certain conditions.

    NOTE: Previous versions of HP T1000j UPS firmware were combined in a softpaq that is available at the following url:  http://www.hp.com/swpublishing/MTX-fe8accb059c642b8b243827a19

    Beginning with version 1.10, updates for the HP T1000j UPS firmware are now published as a separate package.
Version:1.10 (21 Oct 2011)
Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


  • Modified the UPS input waveform detection scheme sub routine. This repaired a unique case in the firmware that allowed the UPS transfer time to battery operation to take excessive time, when utility dropped down from 100 volts to 60 volts under certain conditions.
  • Modified the Advanced Voltage Regulation (AVR) detection scheme by reducing the number of cycles required to detect an out of tolerance voltage condition. This repaired an issue in the firmware that allowed the UPS to stay in its current AVR mode and not perform a buck or boost cycle quick enough, which resulted in the output voltage falling outside of the output voltage specification when utility dropped down from 100 volts to 60 volts under certain conditions.

    NOTE: Previous versions of HP T1000j UPS firmware were combined in a softpaq that is available at the following url:  http://www.hp.com/swpublishing/MTX-fe8accb059c642b8b243827a19

    Beginning with version 1.10, updates for the HP T1000j UPS firmware are now published as a separate package.


Subscribe to driver and support alerts

Sign up now for customized driver, security, patch, and support email alerts.
Type: Firmware - UPS
Version: 1.10(21 Oct 2011)
Operating System(s):
OS Independent

Description

This softpaq includes firmware for the HP T1000j Uninterruptible Power System (UPS). Detailed instructions for performing the firmware update are included in the softpaq.

Installation Instructions

To ensure the integrity of your download, HP recommends verifying your results with this MD5 Checksum value:

d2ee8e676c92656adc1584c776288426 SP55015.EXE

Reboot Requirement:
Reboot may be required after installation for updates to take effect and hardware stability to be maintained.


Installation:
Download the SoftPaq to a directory on your hard drive and change to that directory.

The file that is downloaded is an executable with a filename according to the SP Number.

Run the SP executable to unpack the firmware and release information.

From that SP directory, use the detailed instructions located in the HP T1000j UPS Firmware Update Instructions.pdf file to perform the update.


Release Notes

End User License Agreements:
Hewlett-Packard End User License Agreement


Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


  • Modified the UPS input waveform detection scheme sub routine. This repaired a unique case in the firmware that allowed the UPS transfer time to battery operation to take excessive time, when utility dropped down from 100 volts to 60 volts under certain conditions.
  • Modified the Advanced Voltage Regulation (AVR) detection scheme by reducing the number of cycles required to detect an out of tolerance voltage condition. This repaired an issue in the firmware that allowed the UPS to stay in its current AVR mode and not perform a buck or boost cycle quick enough, which resulted in the output voltage falling outside of the output voltage specification when utility dropped down from 100 volts to 60 volts under certain conditions.

    NOTE: Previous versions of HP T1000j UPS firmware were combined in a softpaq that is available at the following url:  http://www.hp.com/swpublishing/MTX-fe8accb059c642b8b243827a19

    Beginning with version 1.10, updates for the HP T1000j UPS firmware are now published as a separate package.

Revision History

Version:1.10 (21 Oct 2011)
Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


  • Modified the UPS input waveform detection scheme sub routine. This repaired a unique case in the firmware that allowed the UPS transfer time to battery operation to take excessive time, when utility dropped down from 100 volts to 60 volts under certain conditions.
  • Modified the Advanced Voltage Regulation (AVR) detection scheme by reducing the number of cycles required to detect an out of tolerance voltage condition. This repaired an issue in the firmware that allowed the UPS to stay in its current AVR mode and not perform a buck or boost cycle quick enough, which resulted in the output voltage falling outside of the output voltage specification when utility dropped down from 100 volts to 60 volts under certain conditions.

    NOTE: Previous versions of HP T1000j UPS firmware were combined in a softpaq that is available at the following url:  http://www.hp.com/swpublishing/MTX-fe8accb059c642b8b243827a19

    Beginning with version 1.10, updates for the HP T1000j UPS firmware are now published as a separate package.